Typical Test Data
T.B. Numbers refer to specific Technical Bulletins which are available on request.

TYPICAL DRY FILM THICKNESS
Unreinforced: 325 microns.
Reinforced - Reemat Standard GFM: 635 microns.

TENSILE ELONGATION
Unreinforced: 200%
Reinforced - Reemat Standard GFM: 10.4%

CHEMICAL RESISTANCE
Standard 10% solutions of acids and alkalis including nitric acid and caustic soda failed to cause breakdown of the membrane. TB 6/S
Resistant to phosphine. TB 100/S

FIRE RESISTANCE
BS.476 Part 7
Class 1 rating on asbestos cement, plus other BS.476 ratings.

APPROXIMATE SOLIDS CONTENT
63.6% by weight; 47.7% by volume.
Specific gravity: 1.365

DRYING TIME
Approximately 4 hours under ideal conditions. Lower temperatures and conditions of higher relative humidity will progressively retard drying; allow 24 hours between coats.

PACK SIZES
10 litres and 25 litres.

[ top ]



Sterisheen Ultra

Typical Test Data
T.B. Numbers refer to specific Technical Bulletins which are available on request.

TYPICAL DRY FILM THICKNESS
Unreinforced:140 microns.
Reinforced - Reemat Standard GFM: 410 microns.
Reinforced - Reemat Lite: 340 microns.
Reinforced - Reemat Decco: 650 microns.

TENSILE ELONGATION
Unreinforced: 40%
Reinforced - Reemat Standard: 11.0%
Reinforced - Reemat Lite: 4.7%
Reinforced - Reemat Decco: 8.8%

CHEMICAL RESISTANCE
Standard 10% solutions of acids and alkalis including nitric acid and caustic soda failed to cause breakdown of the membrane. TB 6/SHN

FIRE RESISTANCE
BS.476 Parts 6 & 7 TB 339/SHN
Combined Class "0" rating.

APPROXIMATE SOLIDS CONTENT
54.5% by weight; 41.6% by volume.
Specific gravity: 1.265

DRYING TIME
At approx. 20ºC./50% R.H., touch dry at 1 hour; through dry at 3 to 4 hours. Lower temperatures or higher relative humidity will progressively retard drying. Overcoating is possible when the coating is touch dry.

PACK SIZES
10 litres and 25 litres.

[ top ]



Sterisept

Typical Test Data
T.B. Numbers refer to specific Technical Bulletins which are available on request.

TYPICAL DRY FILM THICKNESS
Unreinforced: 72 microns.
Reinforced - Reemat Standard GFM: 360 microns.
Reinforced - Reemat Lite: 320 microns.
Reinforced - Reemat Decco: 625 microns.

TENSILE ELONGATION
Initial : 50% (minimum); Aged: 20% (maximum)
Reinforced - Reemat Standard: 12.0%
Reinforced - Reemat Lite: 4.5%
Reinforced - Reemat Decco: 11.0%

CHEMICAL RESISTANCE
Standard 10% solutions of acids and alkalis, including nitric acid and caustic soda, failed to cause breakdown of the membrane. TB 482/SPT

FIRE RESISTANCE
Indicative test results to BS.476 Parts 6 & 7 give a Class "0" rating.TB 484/SPT, 485/SPT

APPROXIMATE SOLIDS CONTENT
49% by weight; 36% by volume.
Specific gravity: 1.25 (nominal).

DRYING TIME
Touch dry in approximately 45 minutes at 10ºC. / 60% R.H., through cure in 1 hour. Touch dry in approximately 30 minutes at 20ºC. / 55% R.H., through cure in 45 minutes. Touch dry in approximately 15 to 20 minutes at 30ºC. / 50% to 60% R.H. Through cure in 30 to 45 minutes. TB 481/SPT

PACK SIZES
10 litres and 25 litres.

[ top ]



Hygiene Sealant

Typical Test Data
T.B. Numbers refer to specific Technical Bulletins which are available on request.

SLUMP RESISTANCE
No slump at 25ºC. when placed in a 25 mm. x 12 mm. vertical channel.

MOVEMENT TOLERANCE
15% in butt joints.

APPROXIMATE SOLIDS CONTENT
78.6% by weight; 68.9% by volume.
Specific gravity: 1.66 to 1.68 (nominal).

DRYING TIMES
At approx. 25ºC. / 50% R.H., skins in 12 to 20 minutes; tack free in 30 to 60 minutes.

COLOUR
White. (Special colours can be produced, subject to minimum batch quantities.)

PACK SIZE
310 ml. plastic cartridges.

[ top ]


Disclaimer: The information contained herein is correct to the best of our knowledge, but it does not necessarily refer to the particular requirements of the customer. If the customer has any particular requirements, it should make them known in writing to Liquid Plastics, and obtain further advice accordingly.